ORDER CODE
* The permissible output torque for shafts must not be exceeded!
MR
Pos.1
Pos.2
Pos.3
Pos.4
12345678 10
Pos.5
The hydraulic motors are mangano-phosphatized as standard.
9
Pos. 8
Pos. 7
Pos.10
Pos. 6
Pos. 9
- Mounting Flange
- (needle bearings)Option
- Port type
- Displacement code
-*Shaft Extensions
(see page 28)
- Design Series
- Special Features (see page 20)1
- Ports
- Drain Port
- Shaft Seal Version
(see page 30)
- flange with “ ” shafts;Q ...B
w- option with “ ” shafts, Lo Pressure Seal or option;N ...B U
.- “ ” shafts with and shaft seals...B D U
NOTES:
omit
F
Q
- Oval mount
, two holes
- Oval mount, four holes
- Square mount, four bolts
omit
N
- none
-
needle bearings
with
omit
E
- Side ports
-
Rear ports
50
80
100
125
160
200
250
315
400
- 51,5 cm
/rev [ 3.14 in /rev]
33
- 80,3 cm /rev [ 4.90 in /rev]
33
- 99,8 cm /rev [ 6.09 in /rev]
33
- 125,7 cm /rev [ 7.67 in /rev]
33
- 159,6 cm /rev [ 9.74 in /rev]
33
- 199,8 cm /rev [12.19 in /rev]
33
- 250,1 cm /rev [15.26 in /rev]
33
- 315,7 cm /rev [19.26 in /rev]
33
- 397,0 cm /rev [24.40 in /rev]
33
VSH
SH
C
VC
CO
K
SA
VCO
VSA
CB
KB
SB
OB
HB
- ø25 straight, Parallel key
A8x7x32 DIN6885
- ø25 straight, Parallel key
A8x7x32 DIN6885
with corrosion resistant bushing
- ø1" straight, Parallel key ¼"x¼"x1¼" BS46
- ø1" straight, Parallel key ¼"x¼"x1¼" Bs46
with corrosion resistant bushing
- ø25,32 splined BS 2059 (SAE 6B)
- ø25,32 splined BS 2059 (SAE 6B)
with corrosion resistant bushing
- ø28,56 tapered 1:10, Parallel key B5x5x14 DIN6885
- ø24,5 splined B 25x22 DIN 5482
- ø24,5 splined B 25x22 DIN 5482
with corrosion resistant bushing
- ø32 straight, Parallel key
A10x8x45 DIN6885
- ø35 tapered 1:10, Parallel key B6x6x20 DIN6885
- splined A 25x22 DIN 5482
- ø1¼" tapered1:8, Parallel key "x "x1¼" BS46
- ø1¼" splined 14T ANSI B92.1 - 1976
omit
- Low pressure shaft seal or Standard shaft seal
for “... ” shaftB
D
- Standard shaft seal
U - High pressure shaft seal (without check valves)
omit
- with drain port
1
- without drain port
omit
- BSPP
(ISO 228)
М
- Metric (ISO 262)
omit
- Factory specified
42
MSOTOR
MR
The following combinations are not allowed: